بررسی آزمایشگاهی و عددی تیر بتن مسلح مقاوم سازی شده با ورق های CFRP

نوع مقاله : مقاله پژوهشی

نویسندگان

1 استادیار گروه مهندسی عمران،واحد فیروزاباد، مرکز میمند،دانشگاه آزاد اسلامی،میمند ایران

2 استادیار،گروه مهندسی عمران، واحد بیضا، دانشگاه آزاد اسلامی، بیضا، ایران

10.22124/jcr.2023.23414.1606

چکیده

متداول ترین روش مقاوم سازی تیرهای بتن مسلح، تقویت خمشی این تیرها با مصالح کامپوزیت می باشد. در مقاله حاضر ابتدا یک تیرتقویت نشده در مقیاس واقعی ساخته شد و در آزمایشگاه تحت بارگذاری چهارنقطه ای قرار گرفت. سپس برای تقویت تیر در ناحیه ی خمشی، تیرمشابهی با استفاده از یک لایه ورق CFRP در ناحیه‌ی خمش تقویت شد و پس از انجام آزمایش، ملاک صحت سنجی مدل‌های عددی قرار گرفت. در مطالعات عددی 5 نمونه تیر بتن مسلح با روش‌های تقویتی مختلف با نرم افزار آباکوس مورد بررسی قرار گرفت که نتایج بدست آمده نشان می دهد تیرتقویت شده با ورق CFRP سراسری با دورپیچ ممتد U شکل، بهترین روش تقویتی به لحاظ ظرفیت و شروع ترک ها می باشد. لازم به ذکر است تقویت تیر در محدوده‌ی میانی تیربتن مسلح تاثیر چندانی بر ظرفیت تیر نداشته اما باعث خارج شدن خرابی از محدوده‌ی خمشی محض تیر می شود.

کلیدواژه‌ها

موضوعات


عنوان مقاله [English]

Experimental and Numerical Investigation of Reinforced Concrete Beam Retrofitted by CFRP Sheets

نویسندگان [English]

  • Babak Mansoori 1
  • Mohamadhossein Ahmadi 2
1 Assistant Professor, Department of Civil Engineering, Firoozabad Branch, Meymand center, Islamic Azad University, Meymand, Iran.
2 Assistant Professor, Department of Civil Engineering, Beyza Branch, Islamic Azad University, Beyza, Iran.
چکیده [English]

Currently, extensive studies are carried out on polymers reinforced with FRP sheets as reinforcement of structures both internally and externally. One of the conventional retrofitting methods for reinforced concrete beams is flexural strengthening of beams with CFRP materials. In this study, a full scale reinforced concrete beam was constructed and evaluated under four-point flexural test. Afterward, a same beam was retrofitted in flexural region by monolayer of CFRP. These experimental tests were carried out to be the basis of verification for numerical specimens. For numerical study, ABAQUS software was used for modeling and analysis of totally five retrofitted reinforced concrete beams. The results show that the fully retrofitted beam with CFRP laminate and U-shape wraps has the best performance in terms of capacity and delay for emergence of cracks. Its worth to say, flexural strengthening in the middle of beam has not notable result in capacity, though, could convey the failure mechanism to out of pure bending region.

کلیدواژه‌ها [English]

  • Retrofit
  • Flexural strength
  • Concrete beams
  • CFRP Sheet