دانشگاه گیلانتحقیقات بتن2008-424212219700101Investigating the Post-Heat Behavior of Self-Compacting Light Aggregate Concrete Containing Spring and Fiberبررسی رفتار پس از حرارت بتن سبک خودتراکم حاوی فنر و الیاف518345510.22124/jcr.2019.9337.1257FAقاسمپاچیدهدانشجوی دکتری سازه، دانشکده مهندسی عمران، دانشگاه سمنان، سمنان، ایران.مجیدقلهکیدانشیار، دانشکده مهندسی عمران، دانشگاه سمنان، سمنان، ایرانJournal Article19700101In this paper, the effect of adding fiber to lightweight (containing Light Expanded Lica Aggregate) self-compacting concrete under high-temperature conditions (25-100, 250-500, 700 ° C) was investigated in the form of compressive, tensile and flexural strength tests. In these experiments, 3 types of fibers, including steel fiber, and polypropylene and steel springs, were used for 0.4% volumetric rate of concrete. In general, the results indicate that the use of steel fiber and spring increases the compressive strength of concrete by up to 20%. Polypropylene fiber can be used to improve the tensile strength of concrete, because it increases up to 70% tensile strength after high temperature conditions. Also, at a temperature of 700 °, the flexural strength of all samples was negligible and were destroyed due to their own weight. Also, due to the severe drop in resistance after a temperature of 500 ° C, after this temperature, self-compacting concrete is not serviceable.در این مقاله، تأثیر افزودن الیاف به بتن سبک (حاوی سبکدانه ی لیکا) خودتراکم تحت شرایط پس از حرارت های بالا (25- 100- 250- 500- 700 درجه ی سانتی گراد) در قالب آزمایشات مقاومت فشاری، کششی و خمشی بررسی شد. در آزمایشات، 3 نوع الیاف شامل الیاف فولادی و پلیپروپیلن و فنر فولادی به میزان 4/0% حجمی بتن استفاده شد. بطور کلی نتایج حاکی از آنست که استفاده از الیاف فولادی و فنر تا 20% مقاومت فشاری بتن را افزایش می دهد. می توان از الیاف پلیپروپیلن در بهبود مقاومت کششی بتن استفاده نمود چراکه تا 70% مقاومت کششی را در شرایط پس از دماهای بالا افزایش می دهد. همچنین در دمای 700 درجه مقاومت خمشی کلیه نمونه ها ناچیز بوده و در اثر وزن خود منهدم شدند. همچنین بعلت افت شدید مقاومت در شرایط پس از دمای 500 درجه، پس از این دما بتن سبک خودتراکم قابلیت خدمترسانی ندارد.https://jcr.guilan.ac.ir/article_3455_1f43b3bcf830ada82db2d8c5e8d38591.pdfدانشگاه گیلانتحقیقات بتن2008-424212219700101Construction and characterization of polymer concrete containing waterborne acrylic resin with low permeability to chlorine and water ionsساخت و مشخصهیابی بتن پلیمری حاوی رزین اکریلیک پایهآبی با قدرت نفوذپذیری پایین نسبت به یون کلر و آب1932345610.22124/jcr.2019.11300.1315FAسحرعبدالهی باغبانTehran Province, Tehran, District 6, 424 Hafez Ave
تهران- خیابان حافظ-پلاک 424منوچهرخراسانیدانشگاه صنعتی امیرکبیر/ دانشکده مهندسی پلیمر و رنگJournal Article19700101In this paper, the effect of three waterborne acrylic resins on physical, mechanical, stability, and permeability of concrete was investigated. For this purpose, concrete samples were prepared with a mass ratio of water to cement and solid-resin to cement equal to 0.445 and 0.05, respectively. Compressive stress tests of 7, 28, and 56 days, tensile strength, chlorine ion accelerated migration, capillary water absorption and initial and final water absorption on the test specimens were performed. It was observed that acrylic resin could act as a superplasticizer and reduce the amount of water needed to increase the fluidity of fresh concrete. Adding a resin with a minimum film formation temperature (MFFT) above the operating temperature reduces the chlorine ion penetration depth and coefficient by 14%. As a general result, it can be said that by accepting a reduction of 20-30%reduction in compressive strength of concrete structures, the fluidity of the fresh concrete, physical and penetration properties of the concrete mix can be increased by the use of the waterborne acrylic resin with MFFT higher than ambient temperature.در این مقاله تاثیر اعمال سه رزین اکریلیک پایهآبی بر روی خواص فیزیکی، مکانیکی، پایداری و نفوذپذیری بتن حاصل بررسی شد. بدین منظور نمونههای بتنی با نسبت وزنی آب به سیمان معادل با 445/0 و جامد رزین به سیمان برابر با 05/0 تهیّه شدند. آزمونهای مقاومت فشاری، مقاومت کششی از هم گسیخته، مهاجرت تسریعیافتهی یون کلر، جذب آب مویینه و ابتدایی و نهایی بر روی آزمونهها انجام شد. مشاهده شد که رزین اکریلیک میتواند به عنوان روانکننده-ی بتن استفاده شود و میزان آب مورد نیاز برای افزایش روانی بتن تازه را کاهش دهد. افزودن رزین با حداقل دمای تشکیل فیلم (MFFT) بالاتر از دمای کارکرد، سبب کاهش نفوذ یون کلر تا 14% شد. بطورکلی میتوان گفت که با قبول کاهش 30-20% در مقاومت فشاری سازههای بتنی و ثابت ماندن برخی ویژگیها، روانی بتن تازه، خواص فیزیکی و نفوذی مخلوط بتن حاوی رزین اکریلیک پایهآبی با MFFT بالاتر از دمای محیط بالابرد.https://jcr.guilan.ac.ir/article_3456_b9bb810e57f96ca9f0ddd138bb5e0ee7.pdfدانشگاه گیلانتحقیقات بتن2008-424212219700101Evaluation of hybrid fiber reinforced concrete subjected to freezing and thawing cycles using relative dynamic modulus of elasticityبررسی دوام بتن با الیاف ترکیبی در برابر چرخههای ذوب و یخبندان به کمک مدول الاستیسیته دینامیکی نسبی3348345410.22124/jcr.2019.10277.1289FAمحمدرضااصفهانیگروه مهندسی عمران ،دانشکده مهندسی، دانشگاه فردوسی مشهد ،مشهدمهرادرجب زادهمهندسی عمران ، موسسه آموزش عالی اقبال لاهوریاحمدرضارمضانیگروه مهندسی عمران، دانشکده مهندسی، دانشگاه فردوسی مشهد، مشهد، ایرانJournal Article19700101Hybrid Fiber Reinforced Concrete, a composite obtained by mixing at least 2 different types of fibers, is extensively explored by researchers due to its superior mechanical properties. The present study is aimed to investigate the effect of incorporation of steel, glass and polypropylene fibers as well as the air entraining admixture on the durability of concrete subjected to freezing and thawing cycles, compressive strength and split tensile strength. In order to evaluate the durability of concrete specimens after subjecting the specimens to freezing and thawing cycles, relative dynamic modulus of elasticity and the percentage of the weight loss were measured in 3 different stages (1) prior to staring the main test (2) after subjecting the specimens to 150 cycles of freezing and thawing (3) after subjecting the specimens to 300 cycles of freezing and thawing. Based on the results of the experimental program it appears that utilization of specific combination of fibers at specific volume fractions along with air entraining admixture results in significant improvement of durability of the concrete specimens. The best performance in freezing and thawing test belongs to the specimen containing 0.5% of PP fibers and 1% of steel fibers in which the relative dynamic modulus of elasticity measured after 300 cycles dropped 5%, while the modulus of elasticity for control specimens decreased 30% after these cycles. It is worth noting that the simultaneous monitoring of modulus of elasticity and the weight loss in a specimen can provide more detailed information on the durability of the specimen.بتن با الیاف ترکیبی که از افزودن حداقل دو نوع مختلف از الیاف به بتن حاصل میشود، به دلیل خصوصیات مکانیکی برتر مورد توجه طراحان قرار گرفته است. در این پژوهش تاثیر استفاده از الیاف فولادی، شیشه، پلیپروپیلن و همچنین افزودنی حبابزا بر روی دوام بتن در برابر چرخههای ذوب و یخبندان، مقاومتهای فشاری و کششی به عنوان پارامترهای تاثیرگذار در عملکرد سازههای بتنی بررسی شده است. به منظور بررسی دوام نمونهها، مدول الاستیسیته دینامیکی نسبی و همچنین کاهش وزن نمونهها به عنوان اصلیترین پارامترهای موجود برای سنجش دوام در 3 مرحلهی پیش از شروع آزمایش، حین انجام آزمایش و پس از 300 چرخه ذوب و یخبندان بررسی و با یکدیگر مقایسه شدهاند. بهترین عملکرد در برابر این چرخهها مربوط به نمونه حاوی 5/0 درصد الیاف پلیپروپیلن، 1 درصد الیاف فولادی و حبابزا میباشد. در این نمونه مدول الاستیسیته دینامیکی نسبی پس از 300 چرخه تنها 5 درصد کاهش یافته است؛ حال آنکه در نمونه فاقد الیاف این میزان به 30 درصد میرسد. همچنین در نمونه حاوی 5/0 درصد الیاف شیشه، مدول الاستیستیه دینامیکی نسبی 13 درصد کاهش یافته است و این کاهش در نمونه حاوی 5/0 درصد الیاف پلیپروپیلن تقریبا 6 درصد میباشد. از طرفی دیگر، استفاده از حبابزا میتواند باعث بهبود مدول الاستسیته دینامیکی نسبی تا 120 درصد شود. لازم به ذکر است، بررسی همزمان تغییرات مدول الاستیسیته دینامیکی نسبی و میزان کاهش وزن در یک نمونه میتواند اطلاعات دقیقتری از دوام بتن در برابر چرخههای ذوب و یخبندان را نمایان سازد.https://jcr.guilan.ac.ir/article_3454_3a8bd07871edd4ff1bccaaa290514cc2.pdfدانشگاه گیلانتحقیقات بتن2008-424212219700101Study of mechanical properties and durability of concrete containing cementitious materials and micro-nano bubbleبررسی خواص مکانیکی و دوام بتن حاوی مکمل سیمانی زئولیت و آب میکرو_نانو حباب4960345710.22124/jcr.2019.9581.1264FAعلی اکبرشیرزادی جاویددانشگاه علم و صنعت ایران - دانشکده مهندسی عمرانمعینخوشروگروه عمران، دانشکده فنی و مهندسی ، دانشگاه خوارزمی، تهران، ایرانعلیکاتبیاستادیار، دانشکده فنی و مهندسی، دانشگاه خوارزمی، تهران، ایرانJournal Article19700101In this paper, the effect of using natural zeolite as a supplementary cementitious material and micro-nano bubble as a substitute for concrete mixture water has been evaluated on the mechanical properties and durability of concrete. The evaluated parameters for properties of modified concrete include: compressive strength, tensile strength, Bending strength, electrical resistivity and water absorption. The results indicate that the use of zeolite and micro-nano bubble in concrete increases the mechanical properties and the durability of concrete. The greatest improvement is related to the two-phase samples from the combination of 10% zeolite and 100% micro-nano bubble, which compressive strength, tensile strength, bending strength and electrical resistivity increase by 15, 14.88, 5.65 and 194.12% respectively, and water absorption decrease by 25.22%. In general, according to the results, it can be concluded that zeolite and micro-nano bubble, improve the mechanical properties and durability of concrete and their combination has the most positive effect on modified concrete.در این مقاله تاثیر استفاده از زئولیت طبیعی به عنوان جایگزین مواد سیمانی و آب میکرو_نانو حباب به عنوان جایگزین آب مخلوط بتن، بر خواص مکانیکی و دوام بتن مورد ارزیابی قرار گرفته است. پارامترهای ارزیابی شده برای بررسی خواص مکانیکی و دوام بتن اصلاح شده شامل: مقاومت فشاری، کششی، خمشی، الکتریکی و جذب آب میباشد. نتایج حاکی از آن است که بیشترین تأثیر استفاده از زئولیت و میکرو_نانوحباب در بتن مربوط به نمونههای دو فازی حاصل از ترکیب 10 درصد زئولیت و 100 درصد میکرو_نانو حباب میباشد که سبب افزایش مقاومت فشاری، کششی، خمشی و الکتریکی به میزان 15، 14 ، 6 و 194 درصد گشته و جذب آب را به میزان 25 درصد کاهش می دهد. به طور کلی با توجه به نتایج میتوان گفت زئولیت و آب میکرو_نانوحباب سبب بهبود خواص مکانیکی و دوام بتن میگردند و ترکیب آنها بیشترین تأثیر مثبت را در تقویت بتن اصلاح شده ایجاد میکند.https://jcr.guilan.ac.ir/article_3457_86bbf4ff00c45d1d1be12647129f67cc.pdfدانشگاه گیلانتحقیقات بتن2008-424212219700101Evaluation and comparison of the application of GRP casing and FRP sheets on the behavior of circular reinforced concrete columns made of normal and high-strength concreteارزیابی و مقایسه کاربرد غلاف GRP و دورپیچ CFRP بر رفتار ستون های استوانه ای بتن مسلح ساخته شده از بتن های معمولی و پرمقاومت6176345810.22124/jcr.2019.11168.1313FAسیدفتح الهساجدیدانشیار، گروه عمران، واحد اهواز، دانشگاه آزاد اسلامی، اهواز، ایران0000-0003-3933-2793محسنشفیعی نیادانشجوی دکتری سازه دانشگاه آزاد اسلامی واحد اهوازJournal Article19700101This paper presents the results of axial pressure testing on reinforced concrete columns (RCC) loaded with confined normal concrete (NC) and high-strength concrete (HSC) using glass-fiber reinforced plastic pipes (GRP) casing as well as carbon fiber reinforced polymer (CFRP). This study aimed to evaluate the behavior and mechanical properties of columns confined with GRP and FRP under pressure loads. The major parameters in the experiments were the types of concrete, the effect of GRP and FRP wrapping, as well as the number of FRP layers. 12 cylindrical RCC (150*600 mm) were prepared and divided into two groups, NC and HSC, and each group was divided into two parts. In each part, one column was without FRP, a column was wrapped with one layer and another column with two layers. All columns were tested under concentrated compression load. The results showed that the utilization of FRP and GRP improved compression capacity and ductility of RCC. The addition of one and two layer-FRP wrapping increased compression capacity in the NC group to an average of 18.5% and 26.5% and in the HSC group to averagely 10.2% and 24.8%. Meanwhile, the utilization of GRP increased the compression capacity of the columns by 4 times in the NC group and 3.38 times in the HSC group. These results indicated that although both FRP and GRP result in confinement, the GRP resulted in increased compression capacity and ductility of the RCC due to higher confinement. Furthermore, the confinement effect was higher on the first group.این تحقیق رفتار ستونهای بتنمسلح ساخته شده از بتنهای معمولی و پرمقاومت که با استفاده از غلاف GRP و همچنین دورپیچ CFRP ، محصور شدهاند، را ارائه میکند. هدف بررسی رفتار و ظرفیت باربری ستونهای محصور با غلاف و دورپیچ تحت بارهای فشاری است. تأثیر نوع بتن، غلاف، دورپیچ و تعداد لایههای دورپیچ بررسی گردید. 12 ستون بتنمسلح استوانهای از بتن-های معمولی و پرمقاومت ساخته شدند؛ ستونها به دو گروه 6تایی از بتن معمولی و بتن پرمقاومت تقسیم شدند، هر گروه به دو بخش 3تایی دستهبندی گردید. بخش اول دارای غلاف و بخش دوم فاقد غلاف بودند. از هر بخش یک ستون فاقد لایه تقویتی بود؛ یک ستون با یکلایه و ستون دیگر با دو لایه ورق دورپیچ شدند. تمام ستونها تحت نیروی فشاری متمرکز آزمایش شدند. نتایج نشان داد که استفاده از دورپیچ و غلاف باعث بهبود مقاومت فشاری و شکلپذیری ستونها گردید. افزودن یک لایه و دو لایه دورپیچ به طور میانگین به ترتیب باعث افزایش%5/18 و %5/26 مقاومت فشاری در گروه اول و %2/10 و %8/24 در گروه دوم گردیدند، درحالی که استفاده از غلاف بهطور میانگین باعث افزایش 4 برابری مقاومت فشاری ستونها در گروه اول و 38/3 برابری در گروه دوم شده است. نتایج حاکی است که گرچه دورپیچ و غلاف هر دو محصوریت ایجاد میکنند، ولی غلاف به خاطر محصوریت بالاتر، تاثیر بسیار بیشتری بر افزایش مقاومت فشاری و شکلپذیری ستونها دارد. بهعلاوه، تاثیر محصوریت بر ستون-های گروه اول بیشتر است.https://jcr.guilan.ac.ir/article_3458_c156efcb5798a3e8d1ffb911ba8ad248.pdfدانشگاه گیلانتحقیقات بتن2008-424212219700101Evaluation of the response of reinforced concrete shear walls with openings under cyclic loadingارزیابی پاسخ دیوارهای برشی بتنآرمه دارای بازشو تحت بارگذاری چرخهای7793345910.22124/jcr.2019.10452.1296FAمحمدبهارلوموسسه آموزش عالی عقیق/شاهین شهر/ اصفهانمهردادحجازیخیابان هزار جریب-دانشگاه اصفهان-دانشکده مهندسی عمران و حمل و نقل-گروه عمرانJournal Article19700101, the effective parameters on the performance of reinforced concrete shear walls, such the amount of longitudinal and transverse rebars, openings, opening aspect ratio, Regular and irregularly aligned openings at the height of the wall and opening distance from the edge of the wall have been studied and the most appropriate parameters for the reinforced concrete shear wall have been provided. Reinforced concrete shear walls of 0.35×6.5×16.5m3 have been under cyclic loading. Non-linear finite element analysis using the ABAQUS code has been performed. Concrete damage plasticity model has been used. A wall with no openings and with minimum longitudinal and transverse reinforcement of has been considered as the control sample and other samples have been compared with it through measures such as load bearing capacity, dissipated energy, and cracking and crushing distributions and patterns. The results show that the presence of openings in concrete shear walls in the amount of 18.65% of the wall surface caused a reduction of 24% resistance and 43% of the initial hardness of the opening wall compared to the sample without opening, irregularly of the opening at the wall height increased by 8% Resistance and 12% hardness of the wall. Also, the strength and hardness of the opening specimens were the distance between the opening and the edge of the wall and the adjacent opening, so that the most suitable openings for the shear wall were a wall with openings up to 1.5 times its width from the edge of the wall.در این تحقیق پارامترهای مؤثر بر عملکرد دیوارهای برشی بتن مسلح، همچون مقدار میلگردهای طولی و عرضی دیوار، بازشو، نسبت ابعاد بازشو، منظم و نامنظمی چیدمان بازشو در ارتفاع دیوار و فاصله بازشو از لبه دیوار مطالعه شده است و مناسبترین حالت پارامترهای مورد بررسی برای حضور بازشو در دیوارهای برشی بتن مسلح ارائه گردیده است. نمونه دیوارهای بتنی با ابعاد m3 5/16× 5/6× 35/0 تحت اعمال همزمان بار چرخهای و بار متمرکز یکنوا در بالاترین قسمت دیوار قرارگرفتهاند. تحلیل غیر خطی با استفاده از نرم افزار المان محدود ABAQUS انجام شده و برای رفتار غیرخطی بتن از مدل پلاستیسیته آسیب استفاده شده است. یک نمونه دیوار بتنی بدون بازشو با حداقل مقدار میلگردهای طولی و عرضی آیین نامهای به عنوان نمونه پایه در نظر گرفته شده و سایر نمونهها از طریق معیارهایی چون ظرفیت باربری، میزان انرژی مستهلک شده، نحوه و توزیع ترک خوردگی و خرد شدگی با آن مقایسه شدهاند. نتایج حاصل نشان میدهد که حضور بازشو در دیوارهای بتنی به میزان 65/18% سطح دیوار باعث کاهش 24% مقاومت و 43% سختی اولیه دیوار بازشودار نسبت به نمونه بدون بازشو شده است، نامنظمی چیدمان بازشوها در ارتفاع دیوار باعث افزایش 8% مقاومت و 12% سختی دیوار شده است. همچنین، مقاومت و سختی نمونههای دارای بازشو تابع فاصله بازشو از لبه دیوار و بازشو مجاور بوده است به نحوی که مناسبترین دیوار برشی بازشودار از نظر مقاومت و سختی، دیواری است که بازشوها به اندازه 5/1 برابر عرض بازشو از لبه دیوار فاصله گرفتهاند.https://jcr.guilan.ac.ir/article_3459_d9dba6b21fb649cd0dbceb59cef762c0.pdfدانشگاه گیلانتحقیقات بتن2008-424212220190622Investigating measurement variations of flexural behavior in preloaded specimens of pozzolanic concrete reinforced with steel and glass fibersبررسی تغییرات رفتار خمشی در نمونه های پیش بارگذاری شده بتن های پوزولانی مسلح به الیاف فولاد و شیشه951113711FAکمیلکریمی مریدانیگروه مهندسی عمران، واحد لاهیجان (مرکز سیاهکل)، دانشگاه آزاد اسلامی، سیاهکل، ایران.Journal Article20181231Flexural behavior investigation of concrete materials is one of the most important issues in evaluating its mechanical behavior and is one of the main criteria for the design of concrete structures. The flexural behavior analysis of concrete specimens in a laboratory can simulate the behavior of concrete in a real scale with acceptable accuracy. Flexural strength, failure energy, bending coefficient and toughness are parameters that can be extracted from concrete bending results. Each of these parameters is important in the complex and sensitive design of high-rise or non-structural structures. In this research, two pozzolans of zeolite and silica ash, as well as two types of steel and glass fibers are used to improve the concrete specificationsThe effect of individual behavior of these materials and their effects simultaneously has been highlighted. The materials used in this project have a significant research background. However, in the combination of materials mentioned, little research has been done; and there are still more studying points. The results of pre-loading concrete fibers represented new aspects of concrete behavior in structural performance. It was observed that in the non-pozzolan specimens, increasing the amount of steel fibers increased flexural strength while increasing the amount of glass fibers did not have a significant effect on increasing flexural strength. Also, in the specimens with mixed pre-loading, with the decrease of the percentage of silica soot, the difference of results is reduced. This trend indicates that zeolite has a more important role in repairing cracks for shorter time intervals. Examination of fracture energy showed that specimens containing 1% steel fiber had the highest fracture energy due to fiber performance. After the specimens are damaged, this process is maintained and it seems that cracking in the fiber specimens does not necessarily lead to disruption of fracture energy changes.<strong>بررسی رفتار خمشی بتن، یکی از موضوعات بسیار مهم در ارزیابی رفتار مکانیکی آن محسوب می شود و یکی از معیارهای اصلی طراحی سازه های بتنی می باشد. با مطالعه و تحلیل رفتار خمشی نمونه های استاندارد بتنی در آزمایشگاه، قابلیت شبیه سازی رفتار بتن ساخته شده در مقیاس واقعی و سازه ای با دقت قابل قبول فراهم می شود. مقاومت خمشی، انرژی شکست، ضریب کشسانی خمشی و چقرمگی پارامترهایی هستند که از نتایج آزمون خمش نمونه های بتنی قابل استخراج می باشند و در طراحی های پیچیده و حساس سازه های بلندمرتبه و یا غیرساختمانی، هر یک از اهمیت خاصی برخوردار هستند. در این پژوهش از دو پوزولان زئولیت و دوده سیلیسی و همچنین دو نوع الیاف فولاد و شیشه جهت بهبود مشخصات بتن بهره برداری شده است. بررسی تأثیر رفتار منفرد هر یک از این مواد و همچنین تأثیر آنها به صورت همزمان (هم افزایی یا تأثیر مخرب) در دستور کار این پروژه قرار می گیرد. هریک از مواد مصرفی بکار برده شده در این پژوهش، دارای پیشینه تحقیقاتی قابل توجهی هستند. با وجود این، تحقیقات بسیار کمی در ترکیب این مواد به منظور بررسی رفتار مکانیکی بتن انجام شده است، از این رو انتظار می رود در مطالعه و کنکاش این مصالح ترکیبی، نکات مبهمی وجود داشته باشد.</strong><strong>استفاده از شرایطی خاص برای آزمون نمونه ها (پیش بارگذاری) این پروژه را از پروژه های متعارف، متمایز می سازد. پیش بارگذاری بتن های الیافی موضوع جدیدی است که می توان با استفاده از نتایج آن به ابعاد جدیدی از رفتار بتن بعد از تغییراتی قابل توجه در عملکرد سازه ای دست یافت</strong><strong>. مشاهده گردید که در طرح های فاقد پوزولان، افزایش مقدار الیاف فولادی باعث افزایش مقاومت خمشی می شود در حالی که افزایش مقدار الیاف شیشه، تاثیر چندانی بر افزایش مقدار مقاومت خمشی ندارد. همچنین در طرح های با پیشبارگذاری ترکیبی که اثر دوده سیلیس کاهش می یابد، با کم شدن درصد دوده سیلیس اختلاف نتایج نیز کمتر می شود که نشان می دهد زئولیت نقش فعال تری در ترمیم ترک برای بازه های زمانی کوتاهتر را دارد. بررسی میزان انرژی شکست نیز نشان داده است که طرح های حاوی 1% الیاف فولادی بیشترین انرژی شکست را داشته اند که مدیون عملکرد الیاف هستند. پس از آسیب دیدگی نیز این روند حفظ شده و به نظر می رسد ترک خوردگی در طرح های الیافی لزوماً منجر به بر هم خوردن روند تغییرات انرژی شکست نمی شود.</strong>https://jcr.guilan.ac.ir/article_3711_d58c8c3d5494d2661cc51adff4f70bc2.pdfدانشگاه گیلانتحقیقات بتن2008-424212220190622Prediction of Compressive Strength of Self-Compacting Concrete Containing Fly Ash Using Multivariate Adaptive Regression Splines (MARS)پیش بینی مقاومت فشاری بتن خودتراکم حاوی خاکستربادی با استفاده از روش اسپلاین رگرسیونی چندمتغیره تطبیقی (مارس)113125390810.22124/jcr.2020.5966.1139FAمحمدجوادطاهری امیریدانشجوی دکترای مهندسی و مدیریت ساخت دانشگاه صنعتی بابلعلیاشرفیانکارشناسی ارشد موسسه آموزش عالی طبری بابل0000-0002-9134-6722جوادبرنجیانرئیس موسسه آموزش عالی طبری بابلامیدلطفی عمراندانشجوی دکترای عمران-سازه دانشگاه گیلانJournal Article20170107Utilization of Self-compacting concrete can reduce expenses of the construction and time, therefore the use of artificial intelligence methods to estimation of concrete properties seems necessery .The main purpose of the study presented in this paper was to investigate the feasibility of using multivariate adaptive regression spline (MARS) for the prediction of 28-day compressive strength of self-compacting concrete with an optimal mixing ratio. Total of 94 dataset collected from the published paper were used in this study. To compare the performance of the technique, prediction was also done using a multilayer perceptron neural network model. MARS model in the training phase model (RMSE=4/250) was better performance than Neural Network (RMSE=4/626). The results of error indices of the testing stage in MARS and Neural Network methods respectively (RMSE=3/007) and (RMSE=4/049) were performed accurately in compressive strength prediction The analysis indicated that the proposed MARS model can gain a high precision, which provides an alternative method for predicting the properties of SCC.استفاده از بتن خودتراکم علاوه بر کاهش زمان ساخت، به کاهش هزینه نیز میانجامد، از اینرو استفاده از روشهای نوین هوشمند مصنوعی جهت تخمین مقادیر خواص بتن خودتراکم ضروری به نظر میرسد. هدف اصلی در این مقاله، امکان استفاده از روش اسپلاین رگرسیونی چندمتغیره (مارس) برای پیشبینی مقاومت فشاری 28 روزه بتن خودتراکم میباشد. در این مطالعه، 109 داده آزمایشگاهی مورد بررسی قرار گرفته است. همچنین برای مقایسه عملکرد روش مارس، دادههای مذبور با روش شبکه عصبی مصنوعی نیز بررسی شد. روش مارس در مرحله آموزش مدل(250/4RMSE=) نسبت به شبکه عصبی (626/4RMSE=) عملکرد بهتری را نشان داد. نتایج بدست آمده از شاخصهای خطا در مرحله آزمون روشهای مارس و شبکه عصبی به ترتیب با (007/3RMSE=) و(049/4 RMSE=) عملکرد مطلوبی در پیشبینی مقاومت فشاری از خود نشان دادند.همچنین تحلیل حساسیت انجام شده در این مطالعه نشان داد سیمان و پودرخاکستربادی بیشترین تاثیر را در توسعه مدل پیشنهادی مارس داشته اند. ارزیابی مدلهای پیشنهادی با استفاده از شاخصهای آماری خطا سرعت و دقت مدل مارس را در پیشبینی خواص بتن مشخص کرده است.https://jcr.guilan.ac.ir/article_3908_71e39bf863a07496be58563efd6bd289.pdfدانشگاه گیلانتحقیقات بتن2008-424212220190622Study The Role of mineral additives on grind ability and quality of cement clinkerبررسی نقش افزودنیهای معدنی در آسیای کلینکر بر قابلیت خردایش و کیفیت سیمان111125346110.22124/jcr.2019.11891.1322FAعطاالهبهرامیهیئت علمی گروه مهندسی معدن دانشگاه ارومیهجعفرعبداللهی شریفهیئت علمی گروه معدن دانشگاه ارومیه و صنعتی ارومیهمحسنعلیلوکارشناس ارشد مهندسی استخراج معدنفاطمهکاظمیدانشجوی دکتری مهندسی معدنJournal Article20181205Aim of this paper is studying the effect of mineral addictive and type of them, on the processing of cement produce and quality of it. For this purpose, preparation of samples of cement clinker with additives of pozzolan, perlite, pumice and also abrasive organic compounds have been investigated their grinding efficiency. Then, concrete blocks with dimensions of 10 × 10 cm were constructed, than tested compressive strength at different ages of 2, 3, 7 and 28 days. Based on the results, the use of mineral additives has led to an increase in the number of Blaine, in other words, additives have played the role of abrasive aid. The mixing plan of 85% of clinker and 15% of pozzolan resulted in the highest amount of blast cement (4546 m2/kg). The use of additives at the age of 2 and 3 days of concrete has reduced the compressive strength. At the age of 28 days, the presence of additives increases its compressive strength compared to the non-use of the additive. The combination of organic abrasives and mineral additives in all cases has led to an increase in concrete bulk and compressive strength. The combination of 15% by weight of pozzolan, 85% clinker, 4% gypsum and 3 g of abrasive organic compound, is the optimum combination of cement.هدف این تحقیق بررسی تاثیر افزودنیهای معدنی بر بازدهی پروسه تولید سیمان و خواص محصول است. بدین منظور با آماده-سازی نمونههایی از کلینکر سیمان با افزودنیهای معدنی و همچنین کمک سایندههای آلی به بررسی بازدهی خردایش آنها پرداخته شده است. سپس بلوکهای بتنی ساخته و بر روی آنها آزمایش تعیین مقاومت فشاری در سنین مختلف انجام گرفته است. براساس نتایج، استفاده از افزودنیهای معدنی موجب افزایش عدد بلین شده است. طرح اختلاط 85 درصد کلینکر و 15 درصد پوزولان منجر به حصول بیشترین مقدار بلین سیمان به میزان (m2/kg) 4546 شده است. استفاده از افزودنیها در سنین 2 و 3 روزه بتن موجب کاهش مقاومت فشاری شده است. در سن 28 روزه بتن، وجود افزودنیها موجب افزایش مقاومت فشاری آن نسبت به حالت عدم استفاده از افزودنی شده است. ترکیب 15 درصد وزنی پوزولان، 85 درصد کلینکر، 4 درصد گچ و 3 گرم کمک ساینده آلی، بهینهترین ترکیب سیمان است.https://jcr.guilan.ac.ir/article_3461_4eb94cfa165d01d4a570a521275204e4.pdfدانشگاه گیلانتحقیقات بتن2008-424212220190622Effects of polyvinyl alcohol fibers (PVA) on Mechanical Properties of concreteبررسی اثر استفاده از الیاف پلی وینیل الکل بر مشخصات مکانیکی بتن127140346210.22124/jcr.2019.12038.1326FAمهدیاسفندی سرافرازگروه مهندسی عمران، دانشکده فنی و مهندسی، دانشگاه آزاد اسلامی واحد تهران غرب، تهران، ایرانمحمد سجادمسعودیگروه مهندسی عمران، دانشکده فنی و مهندسی، دانشگاه آزاد اسلامی واحد تهران غرب، تهران، ایرانایوبکریمیگروه مهندسی عمران، دانشکده فنی و مهندسی، دانشگاه آزاد اسلامی واحد تهران غرب، تهران، ایرانJournal Article20190120Concrete is a brittle material and the deficiencies of concrete such as low tensile strength, small ultimate strain and shrinkage are greatly limited the application of concrete. Fiber-reinforced concrete (FRC) is concrete containing fibrous material which increases its structural integrity. It contains short discrete fibers that are uniformly distributed and randomly oriented. Polyvinyl alcohol (PVA) fiber is as one of the most appropriate polymeric fibers to be used for fiber-reinforced concrete. This research demonstrates the effects of PVA fibers on the mechanical properties of concrete mixtures. This paper presents an experimental study on the properties of fresh and hardened concrete that was built with Polyvinyl alcohol fiber. For this purpose, five fiber fractions of PVA (0, 0.25, 0.5, 0.75 and 1%) were used in the mixtures. The tests include slump, density, compressive strength, splitting tensile strength, flexural strength, and modulus of elasticity. Test results showed that after the addition fibers, the workability Property of concrete was reduced. Also, it was seen that PVA fiber meaningfully increase the static properties of concrete as well as improving its post-peak response and ductile behavior.<br />Moreover, high ratios of PVA fiber in the concrete mixture caused negative effects on the compressive strength of concrete. Finally, the optimum percentages of PVA fiber corresponding to the most significant increases in the mechanical properties were presented.در چند سال اخیر استفاده از بتنهای مسلح شده با الیاف رشد زیادی داشته است. بهبود خصوصیات مکانیکی، افزایش میزان جذب انرژی، افزایش مقاومت کششی و خمشی و مقاومت در برابر ضربه بخشی از تأثیر الیاف بر بتن است. الیاف به دلیل خاصیت پل زدن بر روی ریزترکها، باعث بهبود رفتار بتن بعد از ایجاد اولین ترک میشوند. الیاف پلی وینیل الکل (Polyvinyl alcohol fiber) به علت مقاومت کششی و مدول الاستیسیته زیاد و عدم آلایندگی محیط زیست یکی از بهترین انواع الیاف برای تسلیح بتن میباشد. در این پژوهش به بررسی تأثیر الیاف پلی وینیل الکل (PVA) بر مشخصات مکانیکی بتن پرداخته میشود. به این منظور پنج مخلوط با مقادیر مختلف PVA (0، 25/0، 5/0، 75/0و 1 درصد حجم بتن) با طول 12 میلیمتر تهیه و آزمایش شد. نتایج حاصل از آزمایشها، جهت ارزیابی تأثیر درصد حجمی الیاف بر مشخصات مکانیکی بتن بررسی گردید. این نتایج نشان داد که با افزایش درصد الیاف PVA مقاومت خمشی، مقاومت کششی و میزان جذب انرژی بتن افزایش یافته اما در صورت استفاده از الیاف بیشتر از 5/0 درصد حجم بتن، مقاومت فشاری بتن کاهش مییابد. نتایج حاصل از این پژوهش نشان میدهد که استفاده از درصد بهینه الیاف معادل 5/0 درصد حجمی بتن، باعث بهبود مقاومت فشاری به میزان 15 درصد و مقاومت خمشی و کششی به میزان 25 درصد میگردد. لذا با توجه به عملکرد مناسب بتنهای حاوی الیافPVA در فشار، کشش و خمش میتوان از این روش در افزایش شکل پذیری و جذب انرژی استفاده نمود.https://jcr.guilan.ac.ir/article_3462_6758998f526b9f8dcdab1182fcebc309.pdf