@article { author = {Mostofinejad, Davood and Moshiri, Niloufar}, title = {Compressive Strength of RC Columns Strengthened with Longitudinal CFRP Composites}, journal = {Concrete Research}, volume = {6}, number = {1}, pages = {7-18}, year = {2013}, publisher = {University of Guilan}, issn = {2008-4242}, eissn = {}, doi = {}, abstract = {Confining RC columns by FRP composites with fibers oriented in the hoop direction is the most common method of strengthening columns. In the present study, however, the application of CFRP composites with fibers aligned along the column’s axis to improve compressive strength of RC columns has been investigated. Global buckling of composite with longitudinal fibers may result in debonding of FRP from column surface, and thus, the compressive load carrying capacity of the strengthened column would not be increased considerably. To limit the global buckling of composite under compression, a newly introduced strengthening method, named as Grooving Method (GM), was utilized in the present study and its effect on postponing the buckling of CFRP fibers when aligned along the column axis was investigated. For this purpose, 12 circular RC columns with diameter of 150 mm and height of 500 mm were tested under axial compression. Experimental results showed that while the effect of installing CFRP with conventional EBR method was negligible on the columns’ load capacity, the grooving method considerably enhanced the columns’ maximum loads.}, keywords = {RC column,CFRP,Buckling,grooving method,Compressive Strengthening}, title_fa = {ظرفیت محوری ستون های بتن آرمه تقویت شده با کامپوزیت CFRP طولی}, abstract_fa = {از جمله روش های پرکاربرد استفاده از کامپوزیت های FRP (Fiber Reinforced Polymer) در مقاوم سازی ستون ها، محصور‌سازی ستون های بتن‌آرمه با استفاده از کامپوزیت با الیاف حلقوی می باشد. با این وجود، در تحقیق حاضر، تاثیر استفاده از کامپوزیت با الیاف در راستای طولی ستون مورد مطالعه قرار گرفته است. در این حالت، وقوع کمانش کلی در کامپوزیت و در نتیجه جدا شدگی آن از سطح بتن، ممکن است باعث عملکرد نامناسب FRP گردد. در تحقیق حاضر، روش شیار‌زنی در نصب کامپوزیت CFRP (CarbonFRP) با الیاف قائم به کار گرفته شد و تاثیر آن در به تاخیر انداختن کمانش CFRP بررسی گردید. بدین منظور 12 ستون بتن آرمۀ دایروی به قطر 150 میلی‌متر و ارتفاع 500 میلی‌متر تحت بارگذاری محوری خالص قرار گرفت. نتایج آزمایش‌ها نشان داد که به کار‌گیری روش شیار‌زنی موجب افزایش قابل ملاحظۀ ظرفیت باربری ستون تقویت شده با کامپوزیت طولی می گردد. این در حالی است که نصب کامپوزیت به روش متداول نصب سطحی، تاثیر چشمگیری در افزایش بار حداکثر ستون نداشت.}, keywords_fa = {ستون بتن آرمۀ دایروی,ظرفیت باربری,کامپوزیت CFRP تحت فشار,کمانش,شیار‌زنی}, url = {https://jcr.guilan.ac.ir/article_844.html}, eprint = {https://jcr.guilan.ac.ir/article_844_c0439d8b91d1afb0d3f1f32df9f7bc31.pdf} } @article { author = {Sharbatdar, M.K. and Qods, A.}, title = {Bending Strengthening of Light Concrete T-Shape Beams Using FRP Sheets}, journal = {Concrete Research}, volume = {6}, number = {1}, pages = {19-33}, year = {2013}, publisher = {University of Guilan}, issn = {2008-4242}, eissn = {}, doi = {}, abstract = {In order to investigate the effect of Composite Fiber Reinforced Polymers (GFRP) on bending strengthening of light weight T-shaped concrete beams in this paper, nine specimens were designed, built and tested. These specimens were divided into A, B & C Groups, according to their conditions and bars arrangement and composite layers. In Group A, beams were designed to have a medium bending defects, while Groups B and C designed for maximum and minimum bending defects.In each group one beam was as reference and the others were strengthened with different numbers of FRP layers. According to observations and results, flexural strength increase of in Group A was from 81% to 116% while that was from 33% to 208% in Group B and 67% to 100% in Group C. And also the effect of using stronger epoxy and anti-slipt material to change shear failure (debonding) to flexural debonding and increasing strength was investigated in this paper.}, keywords = {T,form beam,flexural strengthening,light structural concrete}, title_fa = {مقاوم‌سازی خمشی تیرهای بتن سبک T شکل با استفاده از ورق‌های GFRP}, abstract_fa = {به منظور بررسی تاثیر ورق‌های کامپوزیت GFRP در تقویت خمشی تیرهای T شکل ساخته‌شده با بتن سبک سازه‌ای، تعداد 10 عدد نمونه تیر آزمایشگاهی طراحی، ساخته و مورد آزمایش قرار گرفتند که نتایج آن در این مقاله ارائه می‌گردد. نمونه‌های آزمایشگاهی با توجه به شرایط و میلگردهای به‌کاررفته در آن‌ها به سه گروه A، B و C متناسب با درصد میلگرد کششی مقطع و تعداد لایه‌های تقویتی تقسیم شدند. طراحی تیرها طوری صورت گرفت که گروه‌های A ، B و C به ترتیب دارای ضعف خمشی میانگین، بیشینه و کمینه باشند. در هر گروه، یک تیر شاهد بوده و تیرهای دیگر با تعداد متفاوت لایه‌های FRP تقویت شدند. با توجه به بررسی‌های انجام‌گرفته و نتایج حاصله مشاهده شد که ظرفیت خمشی تیرهای گروه A بین 81 تا 116 درصد، گروه B بین 33 تا 208 درصد، گروه C بین 67 تا 100 درصد افزایش‌یافته و تغییر شکست جداشدگی ورق‌ها از حالت برشی به خمشی و افزایش ظرفیت خمشی و برشی با به‌کارگیری چسب مخصوص و مواد ضد لغزش در این مقاله بررسی شد.}, keywords_fa = {GFRP,تیرهای T شکل,مقاوم‌سازی خمشی,بتن سبک سازه‌ای}, url = {https://jcr.guilan.ac.ir/article_845.html}, eprint = {https://jcr.guilan.ac.ir/article_845_316752ae0059f8bb43cfa2027242bd80.pdf} } @article { author = {Rezaie, F. and Jafari Radniya, Sh.}, title = {Behavior of Reinforced Concrete Frames Braced with a Combination of X and knee Bracing}, journal = {Concrete Research}, volume = {6}, number = {1}, pages = {35-52}, year = {2013}, publisher = {University of Guilan}, issn = {2008-4242}, eissn = {}, doi = {}, abstract = {In this study, 4 and 8 story reinforced concrete frames retrofitted with X and Knee bracing systems using SAP2000 V14 software and nonlinear static analysis. Then the behavior of these two systems are compared with each other and according to standard 2800 requirements, X-bracing system are located on the lower stories. Static analysis is performed using a uniform and triangular load patterns. Nonlinear plastic hinges have been assigned to the each seismic elements (beams and columns of moment resisting frame, steel bracing and knee elements). Models are chosen such that the participation of moment frame columns and steel bracing in different models have varied. The results indicate that in the X-braced reinforced concrete frames, large tensile forces are applied to the adjacent columns of steel bracing, especially in the lower stories. This problem cause forming plastic hinges in the columns. Also, reinforced concrete frames with knee bracing have the low strength and stiffness, while it is not always more ductile than X bracing. In this research combination of two systems, X and knee bracing, at the height indicate a bracing system that has desirable features of two bracing systems simultaneously and disadvantages of each system can be modified by the other.}, keywords = {RC Frame,X,bracing,Knee bracing,Bracing Participation,Pushover Analysis}, title_fa = {بررسی رفتار قاب‌های بتن‌مسلحِ مهاربندی‌شده با ترکیب مهاربند ضربدری و زانویی}, abstract_fa = {در این مقاله قاب‏های بتن‏مسلح 4 و 8 طبقه با مهاربند ضربدری و زانویی مقاوم‏سازی شده و در نرم‌افزار SAP2000 V14 تحت تحلیل استاتیکی غیرخطی قرار گرفته‏اند. سپس رفتار این دو سیستمِ مهاربندی با یکدیگر مقایسه شده و مطابق توصیۀ آیین‏نامۀ 2800 به گونه‏ای در ارتفاع قاب ترکیب شده‏اند که مهاربند ضربدری همواره در طبقات پایین‏تر قرار بگیرد. تحلیل استاتیکی با استفاده از الگوهای بار مثلثی و یکنواخت انجام شده‏است. تخصیص رفتار غیرخطی به اعضای لرزه‏ای (تیر و ستون‏های قاب خمشی، مهاربندهای فولادی و اعضای زانویی) با تعریف مفاصل پلاستیک برای آن‏ها صورت گرفته‏است. مدل‏های مورد بررسی به گونه‏ای انتخاب شده‏اند که سهم مشارکت ستون‏های قاب خمشی و مهاربندهای فولادی در مدل‏های مختلف، متغیر باشد. نتایج تحقیق نشان می‌دهد، مشکل مهاربند ضربدری در قاب‏های بتن مسلحِ مهاربندی‏شده با این سیستم آن است که نیروهای کششیِ بزرگی از مهاربند به ستون‏های مجاورِ آن در طبقات پایین (خصوصاً زمانی‌که سهم مشارکت مهاربند زیاد باشد) منتقل می‌شود و همین مساله سبب تشکیل مفاصل پلاستیک در ستون می‏شود. هم‏چنین مشکل مهاربند زانویی در قاب‏های بتن‏مسلح مهاربندی‏شده با این سیستم، مقاومت و سختی پایین این مهاربندها می‏باشد، ضمن آن‏که این سیستم همواره از مهاربند ضربدری شکل‏پذیرتر نیست. در این مقاله ترکیب این دو سیستم مهاربندی در ارتفاعِ قاب سیستمی نتیجه داده‏است که ویژگی‏های مطلوب هر دو سیستم را همزمان دارد و نقاط ضعف هر سیستم توسط دیگری اصلاح می‏شود.}, keywords_fa = {: قاب بتن‏مسلح,مهاربند ضربدری,مهاربند زانویی,مشارکت مهاربند,تحلیل بارافزون}, url = {https://jcr.guilan.ac.ir/article_846.html}, eprint = {https://jcr.guilan.ac.ir/article_846_8667acf5c993c8e60aee3832106582a5.pdf} } @article { author = {Madandoust, R. and Ranjbar, M. M. and Mousavi, S.Y.}, title = {Combined Effect of Silica Fume and Zeolite on The Fresh and Hardened Properties of Self-Compacted Concrete}, journal = {Concrete Research}, volume = {6}, number = {1}, pages = {53-71}, year = {2013}, publisher = {University of Guilan}, issn = {2008-4242}, eissn = {}, doi = {}, abstract = {The usages of different additions as a cement replacement in the production of self-compacted concrete (SSC) can lead to a lower material cost, lower environmental pollution, energy consumption and recycling by-product materials. Although, the inclusion of additions may enhance certain properties of SCC, the others may be worsening. To overcome this problem, the combined use of the additions has been recently recommended by researchers. In this respect, the main objective of the present study is to investigate the fresh and hardened properties of SCC made with binary and ternary cementitious blends of silica fume and zeolite. Fresh properties of SCC will be examined by slump flow, visual stability index, T50, V-funnel, L-box and sieve segregation resistance tests. The hardened properties were tested for compressive strength (at different ages), splitting tensile strength, initial and final absorption. To simulate the real-world applications, slump flow and compressive strength changes with hauling time were also considered. The fresh concrete test results revealed that by substituting optimum levels of silica fume and zeolite in SCC, satisfactory workability and rheological properties can be achieved. Silica fume inclusion enhanced both early ages and long-term strength of SCC with zeolite. Moreover, reduction in the slump flow retention of the SCC mixtures containing zeolite was compensated by using silica fume.}, keywords = {self,compacted concrete,Workability,Strength,Hauling time}, title_fa = {بررسی تاثیر استفاده ترکیبی از دودۀ سیلیس و زئولیت بر خواص بتن تازه و سخت‌شده خودتراکم}, abstract_fa = {استفاده از انواع پُرکننده به عنوان جایگزین بخشی از سیمان مصرفی در بتن خودتراکم می‌تواند باعث کاهش هزینه‌ها، کمتر شدن آلودگی زیست‌محیطی، صرفه‌جویی در مصرف انرژی و بهرمندی از محصولات جانبی کارخانجات تولیدی شود. با این‌حال، هر‌چند وجود پُرکننده‌ها باعث بهبود خاصیتی از بتن خودتراکم می‌شود ولی ممکن است باعث تنزل خاصیت دیگری شود. یکی از راه‌هایی که اخیراً توسط محققان برای کاهش اثرات منفی پُرکننده‌ها در بتن خودتراکم مورد توجه قرار گرفته است، استفاده از آنها به‌صورت ترکیبی می‌باشد. هدف اصلی این مطالعه آن است که خواص بتن تازه و سخت شدۀ خودتراکم حاوی ترکیب دوگانه و سه‌گانه سیمان، دودۀ سیلیس و زئولیت را مورد ارزیابی قرار دهد. خواص بتن تازه شامل جریان اسلامپ، زمان رسیدن جریان اسلامپ به قطر 50 سانتی‌متر (T50)، قیف V شکل، جعبۀ L شکل، شاخص پایداری چشمی و الک پایداری می‌باشد. خواص بتن سخت شده نیز برای مقاومت فشاری (در سنین مختلف شامل 3، 7، 14، 28 و 90 روزگی)، مقاومت کششی و جذب آب (اولیه و نهایی) آزمایش شده است. همچنین برای مدلسازی رفتار واقعی بتن در کارهای اجرائی، جریان اسلامپ و مقاومت فشاری با گذشت زمان انتقال تخمین زده شده است. نتایج بتن تازه نشان می‌دهد که با نسبت ترکیب مناسب دودۀ سیلیس و زئولیت در بتن خودتراکم، پایداری و خاصیت رئولوژیکی مطلوب به‌دست خواهد آمد. همچنین افزودن دودۀ سیلیس باعث افزایش مقاومت فشاری اولیه و نهایی بتن خودتراکم حاوی زئولیت می‌گردد. از طرفی کاهش ابقاء جریان اسلامپ در نمونه‌های حاوی زئولیت با افزودن دودۀ سیلیس تا حدودی جبران می‌گردد.}, keywords_fa = {بتن خود‌تراکم,کارائی,مقاومت,زمان انتقال}, url = {https://jcr.guilan.ac.ir/article_847.html}, eprint = {https://jcr.guilan.ac.ir/article_847_c77ac96d6f8e929d4568c20467adce9a.pdf} } @article { author = {Sadrmomtazi, A. and nosrati, H. and Tahmouresi, M.H.}, title = {Evaluation of Fiber Reinforced Concrete Containing Recycled Concrete Aggregates with Non-Destructive Methods}, journal = {Concrete Research}, volume = {6}, number = {1}, pages = {73-86}, year = {2013}, publisher = {University of Guilan}, issn = {2008-4242}, eissn = {}, doi = {}, abstract = {The use of concrete in the construction industry is growing day by day. Due to the limited life span of concrete structures and also the destruction of concrete structures by natural factors such as earthquakes, floods, hurricanes and ... we will always faced with massive amounts of waste concrete that will cause environmental damages. On the other hand natural resources are also limited for generating aggregates that in near future we should use waste concretes as recycled concrete aggregates for an alternative of natural aggregates to save the natural resources. In this study, the replacement proportion of fine and coarse recycled concrete aggregates with conventional aggregates, is the similar percentages of 0, 25, 50, 75 and 100%, which will include 5 mixing design. With increased use of recycled concrete aggregate, reduction of recycled concrete properties, a increase in water absorption and decrease in slump concrete can be observed that it has been tried to compensate this loss in the slump by using super plasticizer. In order to improve the engineering properties of recycled concrete and Study the Effect of polypropylene fibers on the properties of recycled concrete, the polypropylene fibers with the length of 6 mm and different volume percentages of 0.1, 0.2 and 0.3 percent were used that formed of 15 mixing design. In this study, the Compressive strength, Drying shrinkage, Water absorption, Ultrasonic pulse velocity, Electrical strength and SEM tests were done on the samples. withIncrease in the mass percentage ofpolypropylene fibersin recycledconcretes, decrease in results ofUltrasonic pula velocity and Water absorption, increase in Electrical strength results and alsonegativeeffectsonthe compressive strength have been observed. Interms of0.1 % by volume of polypropylenefibersinconcretedesign, Drying shrinkage improvedbutwith using 0.2and0.3 % by volume ofpolypropylenefibers, the Drying shrinkage increasedComparedwithsampleswithnofibers.}, keywords = {Recycled concrete aggregate,Drying shrinkage,electrical strength,Ultrasonic pulse velocity,poly,propylene fibers}, title_fa = {ارزیابی خصوصیات بتن الیافی حاوی سنگدانه‌های بازیافتی بتنی با استفاده از روش‌های غیر‌مخرب}, abstract_fa = {استفاده از بتن در صنعت ساخت و ساز روز به روز در حال افزایش است. با توجه به محدودیت عمر سازه‌های بتنی و همچنین تخریب سازه‌های بتنی در اثر عوامل طبیعی نظیر زلزله، سیل، طوفان و ... ، همواره با حجم انبوهی از بتن‌های تخریبی مواجه خواهیم بود که سبب تخریب محیط‌زیست خواهند شد. از طرفی منابع معدنی جهت تولید سنگدانه‌ها نیز محدود می‌باشند که در آینده‌ای نه چندان دور ناگزیر باید از این بتن‌های تخریبی به عنوان جایگزینی برای سنگدانه‌های طبیعی استفاده نمود تا بتوانیم منابع طبیعی را حفظ نمائیم. در این پژوهش نسبت جایگزینی ریزدانه و درشت‌دانۀ بازیافتی بتنی با سنگدانه‌های معمولی برابر با درصدهای مشابه 0 ، 25 ،50 ، 75 و 100 % می‌باشد. با افزایش استفاده از سنگدانه‌های بازیافتی بتنی، کاهش در خصوصیات بتن بازیافتی، افزایش جذب آب و افت اسلامپ بتن مشاهده می‌شود که با استفاده از فوق‌روان‌کننده سعی در جبران این کاهش اسلامپ شده است. به منظور بهبود خواص مهندسی بتن بازیافتی و همچنین بررسی تاثیر الیاف پلی‌پروپیلن بر خواص بتن بازیافتی، از الیاف پلی‌پروپیلن به طول 6 میلی‌متر و با درصدهای حجمی مختلف 1/0 ، 2/0 و 3/0 استفاده شده است. در این تحقیق آزمایش‌های مقاومت فشاری، انقباض خشک، جذب آب، سرعت امواج فراصوتی، مقاومت الکتریکی و عکس‌برداری توسط میکروسکوپ الکترونی روبشی (SEM) بر روی نمونه‌ها انجام گرفته است. با افزایش درصد حجمی الیاف پلی‌پروپیلن در بتن‌های بازیافتی، کاهش سرعت امواج فراصوتی و درصد جذب آب نمونه‌ها، افزایش نتایج مقاومت الکتریکی نمونه‌ها و همچنین تاثیر نسبتاً منفی بر مقاومت‌های فشاری مشاهده شده است. در شرایط استفاده از 1/0 درصد حجمی الیاف پلی‌پروپیلن در طرح‌های بتنی، انقباض نمونه‌ها بهبود می‌یابد ولی با استفاده از 2/0 و 3/0 درصد حجمی در طرح‌های بتنی، شاهد افزایش انقباض نمونه‌ها نسبت به طرح‌های فاقد الیاف خواهیم بود.}, keywords_fa = {سنگدانه‌های بازیافتی بتنی,انقباض,مقاومت الکتریکی,سرعت امواج فراصوتی,الیاف پلی‌پروپیلن}, url = {https://jcr.guilan.ac.ir/article_849.html}, eprint = {https://jcr.guilan.ac.ir/article_849_1e655d2d1ea302859ef9c1c951c240a1.pdf} } @article { author = {Shirzadi Javid, A.K. and Rahmati, B.}, title = {A New Method of Mix Design for Self-Consolidating Concrete Based on Compressive Strength}, journal = {Concrete Research}, volume = {6}, number = {1}, pages = {87-102}, year = {2013}, publisher = {University of Guilan}, issn = {2008-4242}, eissn = {}, doi = {}, abstract = {Self- consolidating concrete (SCC) mix design should consider the appropriate characteristics in terms of workability, rheology, strength and durability simultaneously. Because of this, already standard method in the world for SCC mix design has not been expressed. In this paper, a new method of SCC mix design based on compressive strength is presented. various parameters such as aggregate gradation, packing density, volumetric ratio of water to powder, water to cement ratio, 28-day compressive strength is considered. Results of mix designs made in the laboratory are perfectly accordant with the values of target, so the proposed method is a real and valid.}, keywords = {self,consolidating concrete; compressive strength; mix design; particle packing density}, title_fa = {روش نوین طرح مخلوط بتن خودتراکم بر پایۀ مقاومت فشاری}, abstract_fa = {طرح بتن خودتراکم باید به نحوی باشد که علاوه بر داشتن مشخصات مناسب از لحاظ کارایی و رئولوژی، از نظر مقاومت و دوام نیز مشخصات فنی مورد انتظار پروژه را برآورده سازد. به همین دلایل تاکنون روش استاندارد و مورد اجماع در دنیا برای طرح مخلوط بتن خود تراکم بیان نشده است. بنابراین با توجه به عدم لحاظ مقاومت فشاری مشخصه و هدف طرح در بسیاری از روش های موجود، در این مقاله سعی شده روشی جدید برای طرح مخلوط بتن خودتراکم بر اساس مقاومت فشاری مطرح شود. در این تحقیق سعی شده است از پارامترهای مختلف از جمله دانه‌بندی مصالح سنگی (که در بسیاری از مقالات تحت عنوان چگالی انباشتگی ذرات سنگی مد نظر قرار گرفته است)، نسبت حجمی آب به پودر، نسبت آب به سیمان، مقاومت فشاری 28 روزه همزمان مورد توجه قرار گیرد. نتایج طرح‌های ساخته شده در آزمایشگاه با این روش کاملا با مقادیری که قبل از ساخت، مشخص شده بوده‌اند مطابقت دارد و نشان‌دهندۀ واقعی و معتبر بودن روش مطرح شده می‌باشد.}, keywords_fa = {بتن خود تراکم,مقاومت فشاری,طرح مخلوط,چگالی انباشتگی ذرات}, url = {https://jcr.guilan.ac.ir/article_848.html}, eprint = {https://jcr.guilan.ac.ir/article_848_d110aab609b3bb3232f4029cc2dd51ce.pdf} } @article { author = {Esmaili, J. and Mohamad Jafari, A.}, title = {Investigating the Effect of Using Macro and Micro Steel Fibers with Nano Silica on the Mechanical Properties of Concrete}, journal = {Concrete Research}, volume = {6}, number = {1}, pages = {103-114}, year = {2013}, publisher = {University of Guilan}, issn = {2008-4242}, eissn = {}, doi = {}, abstract = {Using fibers with different sizes and types part plays more important roles in energy absorption capability of reinforced concrete structures. The effects of different sizes and proportions of fibers on energy absorption capability, bending strength, tensile and compressive strength of concrete have been investigated in this work. Steel fibers have been used to improve the post fracture behavior of concrete and pozzolanic materials have been added to concrete to increase the strength of transition zone. In this regard, the combination of fibers in different sizes for bridging the cracks at different stages of the crack growth and also using nano silica with high surface energy and reactivity can be considered. Simultaneous use of mentioned additives can improve the properties of concrete in the case of using appropriate mix design. Different mix designs containing combinations of different types of steel fibers and micro silica and nano silica have been tested and an optimized mix design of concrete with improved mechanical properties has been reached. Energy absorption capability, bending strength, tensile and compressive strengths can be mentioned as those mechanical properties.}, keywords = {Macro steel fiber,Micro steel fiber,Nano silica,micro silica,Flexural strength,Energy absorption capability}, title_fa = {بررسی اثر استفاده از ترکیب الیاف فولادی ماکرو و میکرو به همراه نانو‌سیلیس بر مشخصه های مکانیکی بتن}, abstract_fa = {افزودن الیاف فولادی جهت بهبود رفتار پس از شکست بتن و مصالح پوزولانی برای افزایش مقاومت ناحیۀ انتقالی کاربرد داشته است. در این راستا ترکیب الیاف در اندازه های متفاوت برای پل زدن و بستن ترک ها در مراحل مختلف شروع تا رشد ترک و همچنین استفاده از نانوسیلیس با انرژی سطحی و واکنش‌پذیری بالا می تواند مورد توجه قرار گیرد. استفادۀ همزمان از افزودنی های ذکر شده نیز میتواند درصورت ترکیب مناسب به تجمیع مزایای ذکر شده در توانمند‌سازی بتن بیانجامد. در این تحقیق با تهیه و بررسی طرح اختلاط‌های مختلف دارای ترکیب‌های متفاوت از انواع الیاف فولادی به همراه دودۀ سیلیسی و نانوسیلیس، ترکیب بهینه‌ای از بتن با مشخصه‌های مکانیکی بهبود یافته به‌دست آمد. از جمله این مشخصه‌های مکانیکی می توان به افزایش قابلیت جذب انرژی و مقاومت خمشی، مقاومت کششی و فشاری بتن اشاره کرد.}, keywords_fa = {ماکرو الیاف فولادی,میکرو الیاف فولادی,نانو سیلیس,دودۀ سیلیسی,مقاومت خمشی,قابلیت جذب انرژی}, url = {https://jcr.guilan.ac.ir/article_842.html}, eprint = {https://jcr.guilan.ac.ir/article_842_8cbbb55dc3792bf40564b5d0950f23ad.pdf} } @article { author = {Foroughi-Asl, A. and Hoseinnejad, F.}, title = {The Effects of Polypropylene Fibers on Mechanical Properties and Permeability of Concrete}, journal = {Concrete Research}, volume = {6}, number = {1}, pages = {115-125}, year = {2013}, publisher = {University of Guilan}, issn = {2008-4242}, eissn = {}, doi = {}, abstract = {In recent years, using of various fibers in concrete mix is growing and each type creates some specific property in concrete. Polypropylene (PP) fiber is a new type fiber with significant advantages in mechanical properties of fibrous concrete. In this research two series of concrete mix were made ( without fibers - control concrete - and with PP fibers in length of 6 and 12 mm and in 0.2, o.4, and o.8 percent of cement content) by local aggregates(sand and gravel), Portland cement, silica fume (as pozzolan), and superplasticizer (as admixture with polycarboxilic base). The specimens were cured for 3, 7 and 28 days and tested for compressive and flexural strength. The specimens elected for measuring the permeability depth were tested under 5 atm. water head after 28 days curing and permeability index was calculated by Valenta equation. Results showed that early compressive strength of fiberous specimens was less than control specimens but by increasing the age of specimens, the strength will be increased and maximum compressive strength was for 28-d specimen with 0.8 percent of PP fiber but the flexural strength of fibrous specimens were more than normal specimens at all ages and the maximum flexural strength was for 28-d specimen with 0.4 percent of PP fiber. Permeability of fibrous specimens was less than normal specimens and the minimum value belongs to specimen with 0.4 percent of PP fiber.}, keywords = {Fibrous concrete,Polypropylene fiber,permeability,Superplasticizer,silica fume}, title_fa = {تاثیر الیاف پلی پروپیلنی برروی خواص مکانیکی و نفوذپذیری بتن}, abstract_fa = {در سال‌های اخیر استفاده از انواع مختلف الیاف در بتن افزایش رو به رشدی داشته است و هر نوع خاص از الیاف موجب بهبود ویژگی مشخصه ای از بتن می گردد، الیاف پلی‌پروپیلنی نیز نوعی الیاف پلیمری هستند که افزودن درصدهای اندک آن موجب بهبودی چشمگیری در خواص بتن می‌شود. در این پژوهش با استفاده از مصالح محلی و مواد افزودنی میکروسیلیس به عنوان جایگزین سیمان و فوق‌روان‌ساز پلی‌کربوکسیلیک دو سری نمونه، نمونه های شاهد و مسلح به الیاف پلی‌پروپیلن رشته‌ای 6 و 12میلی‌متری، به میزان 2/0، 4/0و 8/0 درصد وزن سیمان ساخته شدند. بعد از عمل‌آوری در اتاقک بخار، آزمایش‌های مقاومت فشاری و کششی در سنین 3، 7 و28 روزه بر روی نمونه‌ها صورت گرفت. نمونه‌های مربوط به نفوذپذیری نیز بعد از 28 روز عمل‌آوری، به مدت 24 ساعت تحت فشار 5 بار، در دستگاه آزمایش نفوذ‌پذیری قرار داده شدند تا با اندازه گیری عمق نفوذ آب، میزان نفوذپذیری با استفاده از رابطه Valenta محاسبه گردید، در نهایت، مقدار درصد الیاف و اثر الیاف بر مقدار نفوذپذیری و تغییرات آن با خواص مکانیکی بتن مورد بحث و بررسی قرارگرفت و مشخص شد که مقاومت فشاری اولیۀ نمونه‌های بتن الیافی نسبت به نمونه‌های شاهد کمتر بوده ولی با افزایش سن نمونه‌ها نتایج برعکس می‌گردند و بیشترین افزایش مقاومت فشاری 28 روزه مربوط به مقدار الیاف مصرفی 8/0% بوده است و لی مقاومت کششی نمونه‌های بتن الیافی از همان سنین اولیۀ بتن نسبت به نمونه شاهد افزایش نشان می‌دادند و نرخ افزایش با بالا رفتن سن بتن بیشتر می‌شد و بیشترین میزان افزایش مقاومت کششی نیز در سن 28 روزۀ بتن و در نمونه‌های بتنی حاوی 4/0% الیاف مشاهده شد. درآزمایش‌های اندازه‌گیری میزان نفوذپذیری نمونه‌ها، ضریب نفوذپذیری کلیۀ نمونه های تسلیح شده با الیاف پلی‌پروپیلنی در مقایسه با نمونۀ شاهدکاهش یافته بود وکمترین مقدارضریب نفوذپذیری در نمونه‌های دارای 4/0% الیاف حاصل شد.}, keywords_fa = {بتن الیافی,الیاف پلی‌پروپیلن,نفوذپذیری,فوق‌روان‌ساز,میکروسیلیس}, url = {https://jcr.guilan.ac.ir/article_843.html}, eprint = {https://jcr.guilan.ac.ir/article_843_602dfafeefa3fbc44987f8c675b9c332.pdf} }